Sticking with the water analogies, amperes, or amps for short, is the amount of water flowing through the hose. The higher the pressure (voltage), the more water flows (amps) out of the hose. In Ohm’s Law, amperage is represented by “I.”

What this means on a service call
Current is the work happening. Voltage can be present at a load, and still no work is done, if no current flows. On a service call, ask the current question early. Is the load drawing current, is it drawing none, or is it drawing more than it should? The answer points you in different directions. No current points to an open path or a load that never started. Too much current points to a load that is working too hard, a short, or a fault that is forcing extra flow through the circuit.
Use the circuit layout to read a current value. In a series circuit, the same current flows through each part. The series example on this site uses 1.2A through a 10 ohm total, with 12V applied. In a parallel circuit, the total current is the sum of the branch currents. The parallel example uses 1A plus 1A for 2A, and later 1A plus 0.5A for 1.5A. If you clamp the main feed, you see the total. If you clamp one branch, you see only that branch. Both readings are useful, but they answer different questions. Write down which conductor you clamped.
A control signal and a load current are not the same job. A control circuit, often 24V, can send a signal with a small current. The line circuit, often 120V, carries the current that runs a motor, a fan, or a heater. Do not judge a motor by a control reading, and do not judge a control by a motor reading. Check the control first to see if the call arrived. Then check the line current to see if the load answered. If the control is present and the line current is 0A, the break is in the line path or in the load itself.
Numbers and measurements you will see
Compare every reading with the wiring diagram, the nameplate, or the manual for the unit in front of you. The examples below come from posts on this site. They show how readings fit together. They are not a rating for every motor or heater.
- 0A. No current is flowing in that conductor. The load may be off, a switch may be open, or the path may be broken. Check voltage upstream before you assume the load failed.
- 1.2A in series. In the series example, 12V divided by 10 ohms gives 1.2A. That same 1.2A flows through each part in the series path. A different reading in a series path means the circuit is not the one in the example, or a part of it has changed.
- 2A in parallel. In the first parallel example, 1A plus 1A gives 2A total. The total is the sum of the branches, even when the branches are equal.
- 1.5A in parallel. In the worked parallel example, 1A plus 0.5A gives 1.5A total. The branches do not have to carry the same current. Resistance in each branch sets its share.
- 0.5A from Ohm’s Law. In the Ohm’s Law example, 5V divided by 10 ohms gives 0.5A. Use that same method to check whether a reading makes sense for the voltage and resistance you have.
- 15A and 18A fuse example. On the circuit breakers and fuses post, a circuit with number 14 wire is rated for 15A with a 15A fuse, and 18A through that circuit is excessive. Excessive current is the reason a fuse or breaker must break the flow before the wire is damaged.
A common mistake
The most common mistake is to clamp more than one conductor at once. A clamp meter reads the field around one conductor. If you clamp a hot and a neutral together, the fields can cancel, and the meter can read 0A even though current is flowing. Clamp one insulated conductor only. Keep the clamp jaws closed, keep the conductor centred in the jaws as far as the meter allows, and take the reading again if the first result does not match the load state.
A second mistake is to break a live circuit to insert a meter in series when a clamp reading would do the job. Breaking a circuit under load can arc, and it puts the meter and the tech in the path of the current. Use a clamp meter around one conductor for a running current check. Save a series meter connection for a test you have planned, with the power state and the meter rating checked first. A third mistake is to read current and stop there. Current alone does not prove voltage is correct, and it does not prove resistance is correct. Use all three together, as in Ohm’s Law, before you change a part.
Check it in the field
- Find the conductor for the load you want to check. Set the clamp meter for the right kind of current and a range that covers the circuit. Check that the jaws are clean and close fully.
- Clamp one insulated conductor only. Keep your hands clear of bare parts. Record the reading, the conductor, and whether the load was off, starting, or running.
- Compare the reading with the nameplate, the diagram, or the manual. If no value is given there, compare the reading with the same load under the same conditions, and record both readings.
- If the reading is 0A and the load should run, check voltage at the load next. If voltage is present and current is 0A, the load or its internal path is open. If voltage is missing, work upstream.
Work with care around live conductors. Do not touch bare metal to get a better clamp position. Do not open a live circuit to insert a meter unless that test is planned and the meter is rated for it. If a reading is far above what the diagram or nameplate shows, stop the load if it is safe to do so, and find the cause before you run it again. If you are unsure, stop and get help.
Related posts
These posts belong together. Use the summary for the short version, then work through each part on its own.
- Voltage, current, and resistance summary: a short recap of voltage, current, and resistance together.
- Voltage: the push that makes current flow, and how to read a voltage test.
- Resistance: what opposition to flow means, and why a load must have resistance.
- Series Circuits: one path for current, with the same current through each part.
- Parallel Circuits: more than one path, with total current as the sum of the branches.
- Ohm’s Law: how voltage, current, and resistance relate, with worked examples.
